Table of Contents | ||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
Introduction
Esta es una guía muy resumida de los pasos necesarios para instalar Rocky Linux. Al realizarla hemos partido de la ISO This is a very brief guide which provides the necessary steps to install Rocky Linux or Red Hat. For this guide, the following ISO has been used: Rocky-9.4-x86_64-minimal.iso
, es posible que en otras versiones algunos pasos cambien.
...
(some steps may vary in other versions).
This guide is meant for reference purposes only and it does not replace any official documentation, which should always be taken into account.
Note: For Red Hat, you must have a valid subscription in order to download the required packages. You must register your subscription before running any dnf
or yum
commands.
Steps to install
...
Descargar la ISO de la web oficial de Rocky, cargarla en su sistema de virtualización y arrancar.
Al arrancar se muestra un asistente gráfico, configurar los siguientes apartados:
...
Idioma y Zona horaria
...
Layout del teclado
...
the operating system
Download the ISO from the official Rocky website. Then upload it to your virtualization system, and boot it up.
Upon booting, a graphical setup wizard is displayed. Configure at least the following sections:
Language, Keyboard, and Time Zone.
Installation destination: Automatic partitioning. Enter and click “Done” to select this mode.
Software Selection → Minimal install.
Configuración de red: En el apartado IPv4, seleccionar Static y añadir las IPs necesarias para cada tipo de instalación (master requiere 2 y los nodos 1), configurando Máscara de red y Gateway correspondiente en cada caso. Luego, configurar DNS en el campo correspondiente.
Usuario del sistema y su contraseña
Recomendación: crear un usuario (p. ej. opengate), con contraseña y con el check de Administrador. No activar ni poner contraseña al usuario root, usaremos sudo con el usuario administrador.
Info |
---|
Si no se configura en este momento la red (o no se configura correctamente), tras reiniciar se puede ejecutar el comando sudo nmtui para configurar la conexión de red. |
...
Network & Host Name: Enter configuration, IPv4 tab. Choose the “Manual” method, then add IP addresses (the Master requires at least two interfaces when deployed with SIP Registrar, see sample screenshot).
Root Password & User Creation.
Recommendation: create a user (e.g., opengate) with a password and check the Administrator option. Do not activate or set a password for the root user; use
sudo
with the administrator user.
Info |
---|
If the network is not configured at this time (or not configured correctly), you can run the command |
Once the installation is complete, restart the machine, eject the installation disk, and verify that it boots up and can be connected via SSH (ssh opengate@ip.ip.ip.ip
donde opengate es el usuario que se ha configurado durante la instalación, where opengate is the user configured during the installation).
Steps to install Docker
Una vez conectado a la consola del sistema, ejecutar los siguientes comandos:
...
Once connected to the system console, execute the following commands:
If you need to modify the network configuration:
Code Block sudo nmtui
Para deshabilitar el Disable the firewall:
Code Block sudo systemctl disable firewalld sudo systemctl stop firewalld
Instalar Install Docker:
Code Block sudo dnf config-manager --add-repo https://download.docker.com/linux/centos/docker-ce.repo sudo dnf -y install docker-ce docker-ce-cli containerd.io docker-compose-plugin sudo systemctl --now enable docker
En caso de instalar en RedHat, el repositorio es diferente, ejecutar estos comandosIf installing on Red Hat, the repository is different. Execute these commands:
Code Block sudo dnf config-manager --add-repo https://download.docker.com/linux/rhel/docker-ce.repo sudo dnf -y install docker-ce docker-ce-cli containerd.io docker-compose-plugin sudo systemctl --now enable docker
Añadir el usuario al grupo “docker” (si no se hace todos los comandos de docker deberán ejecutarse con Add the user to the "docker" group (if this is not done, all Docker commands will need to be executed with sudo):
Code Block sudo usermod -a -G docker $(whoami)
Tras ejecutar este comando es necesario realizar un logout y volver a conectar para que cargue los permisos. Salir con
exit
y volver a establecer la conexión ssh.Una vez conectado de nuevo, verificar que docker está funcionando con el comando
docker info
que mostrará una información similar a la siguienteAfter executing this command, it is necessary to log out and reconnect for the permissions to take effect. Logout withexit
and then re-establish the SSH connection.Once reconnected, verify that Docker is running with the command
docker info
, which will display information similar to the following:Code Block [opengate@localhost ~]$ docker info Client: Docker Engine - Community Version: 26.1.3 Context: default Debug Mode: false Plugins: buildx: Docker Buildx (Docker Inc.) Version: v0.14.0 Path: /usr/libexec/docker/cli-plugins/docker-buildx compose: Docker Compose (Docker Inc.) Version: v2.27.0 Path: /usr/libexec/docker/cli-plugins/docker-compose ...
Other OS level configuration
NTP synchronization
...
Multiple IP addresses
If you do not configure them using the install user interface, start the console configuration with sudo nmtui
, select the appropriate connection, then use the “Add…” option inside Addresses section to add the new IP.
...
For Azure installations, follow the official documentation https://learn.microsoft.com/en-us/azure/virtual-network/ip-services/virtual-network-multiple-ip-addresses-portal#red-hat-enterprise-linux-and-others
NTP synchronization
By default, it is configured to sync with public servers. If you want to configure it to sync with the machine running OpenGate Proxy Server, edit the file /etc/chrony.conf
, remove the public servers, and add the following instead:
Code Block |
---|
server ip.ip.ip.ip iburst trust |
Siendo Where ip.ip.ip.ip
la dirección IP de la máquina de OpenGate Proxy Server, en la que previamente se ha activado el servidor NTP (consultar pinstallgude).
Email service
En el Master es necesario instalar “postfix” para poder enviar los emails de buzones de voz is the IP address of the OpenGate Proxy Server machine.
In the OpenGate Proxy Windows machine the NTP Server can be enabled with the following steps:
Disable the Windows NTP client. You must first open the date and time configuration settings, select the Internet Time tab and click on Change settings. Next, uncheck the Synchronize with an Internet time server box, as shown below:
Enable the Windows NTP server. You must first create a file named
NTPServerEnable.reg
with the following:Code Block Windows Registry Editor Version 5.00 [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\W32Time\TimeProviders\NtpServer] "Enabled"=dword:00000001 [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\W32Time\Config] "AnnounceFlags"=dword:00000005
Run the
NTPServerEnable.reg
file created and accept the prompt to import the data into the registry. Open a command prompt as administrator and issue the following commands:Code Block sc config w32time start=auto net start w32time
Email service
On the OpenGate Master node, it is necessary to install "postfix" in order to send voicemails:
Code Block |
---|
sudo dnf install postfix sudo systemctl --now enable postfix |