Table of Contents | ||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
Introduction
Esta es una guía muy resumida de los pasos necesarios para instalar Rocky Linux. Al realizarla hemos partido de la This is a very brief guide to the steps necessary to install Rocky Linux or Red Hat. For this guide, we used the ISO Rocky-9.4-x86_64-minimal.iso
, es posible que en otras versiones algunos pasos cambien.
...
; some steps may vary in other versions.
This guide is for reference only and does not replace any official documentation, which should always be taken into account.
Note: for Red Hat you must have a valid subscription in order to download the required packages. You must register the subscription before running any dnf
or yum
commands.
Steps to install OS
Descargar la ISO de la web oficial de Rocky, cargarla en su sistema de virtualización y arrancar.
Al arrancar se muestra un asistente gráfico, configurar los siguientes apartados:
Idioma y Zona horaria
Layout del teclado
Destino de la instalación -- > Automático: Ingresar y aceptar sin modificar nadaUpon booting, a graphical setup wizard is displayed. Configure at least the following sections:
Language, Keyboard, and Time Zone.
Installation destination: Automatic partitioning. Enter and click “Done” to select this mode.
Software Selection → Minimal install.
Configuración de red: En el apartado IPv4, seleccionar Static y añadir las IPs necesarias para cada tipo de instalación (master requiere 2 y los nodos 1), configurando Máscara de red y Gateway correspondiente en cada caso. Luego, configurar DNS en el campo correspondiente.
Usuario del sistema y su contraseña
Recomendación: crear un usuario (p. ej. opengate), con contraseña y con el check de Administrador. No activar ni poner contraseña al usuario root, usaremos sudo con el usuario administrador.
Download the ISO from the official Rocky website, upload it to your virtualization system, and boot it up.
Info |
---|
Si no se configura en este momento la red (o no se configura correctamente), tras reiniciar se puede ejecutar el comando sudo nmtui para configurar la conexión de red. |
...
Network & Host Name: enter configuration, IPv4 tab. Choose “Manual” method, then add IP addresses (the Master requires at least two interfaces when deployed with SIP Registrar, see sample screenshot).
Root Password & User Creation.
Recommendation: create a user (e.g., opengate) with a password and check the Administrator option. Do not activate or set a password for the root user; we will use
sudo
with the administrator user.
Info |
---|
If the network is not configured at this time (or not configured correctly), you can run the command |
Once the installation is complete, restart the machine, eject the installation disk, and verify that it boots up and can be connected via SSH (ssh opengate@ip.ip.ip.ip
donde opengate es el usuario que se ha configurado durante la instalación, where opengate is the user configured during the installation).
Steps to install Docker
Una vez conectado a la consola del sistema, ejecutar los siguientes comandos:
...
Once connected to the system console, execute the following commands:
If you need to modify the network configuration:
Code Block sudo nmtui
Para deshabilitar el Disable the firewall:
Code Block sudo systemctl disable firewalld sudo systemctl stop firewalld
Instalar Install Docker:
Code Block sudo dnf config-manager --add-repo https://download.docker.com/linux/centos/docker-ce.repo sudo dnf -y install docker-ce docker-ce-cli containerd.io docker-compose-plugin sudo systemctl --now enable docker
En caso de instalar en RedHat, el repositorio es diferente, ejecutar estos comandosIf installing on Red Hat, the repository is different; execute these commands:
Code Block sudo dnf config-manager --add-repo https://download.docker.com/linux/rhel/docker-ce.repo sudo dnf -y install docker-ce docker-ce-cli containerd.io docker-compose-plugin sudo systemctl --now enable docker
Añadir el usuario al grupo “docker” (si no se hace todos los comandos de docker deberán ejecutarse con Add the user to the "docker" group (if this is not done, all Docker commands will need to be executed with sudo):
Code Block sudo usermod -a -G docker $(whoami)
Tras ejecutar este comando es necesario realizar un logout y volver a conectar para que cargue los permisos. Salir con
exit
y volver a establecer la conexión ssh.Una vez conectado de nuevo, verificar que docker está funcionando con el comando
docker info
que mostrará una información similar a la siguienteAfter executing this command, it is necessary to log out and reconnect for the permissions to take effect. Logout withexit
and then re-establish the SSH connection.Once reconnected, verify that Docker is running with the command
docker info
, which will display information similar to the following:Code Block [opengate@localhost ~]$ docker info Client: Docker Engine - Community Version: 26.1.3 Context: default Debug Mode: false Plugins: buildx: Docker Buildx (Docker Inc.) Version: v0.14.0 Path: /usr/libexec/docker/cli-plugins/docker-buildx compose: Docker Compose (Docker Inc.) Version: v2.27.0 Path: /usr/libexec/docker/cli-plugins/docker-compose ...
Other OS level configuration
Multiple IP addresses
If you do not configure them using the install user interface, start the console configuration with sudo nmtui
, select the appropriate connection, then use the “Add…” option inside Addresses section to add the new IP.
...
NTP synchronization
Por defecto está configurada para sincronizar con servidores públicos. Si se quiere configurar para que sincronice con la máquina en la que se ejecuta OpenGate Proxy Server, editar el fichero /etc/chrony.conf
eliminar los servidores públicos y añadir en su lugarFor Azure installations, follow the official documentation https://learn.microsoft.com/en-us/azure/virtual-network/ip-services/virtual-network-multiple-ip-addresses-portal#red-hat-enterprise-linux-and-others
NTP synchronization
By default, it is configured to sync with public servers. If you want to configure it to sync with the machine running OpenGate Proxy Server, edit the file /etc/chrony.conf
, remove the public servers, and add the following instead:
Code Block |
---|
server ip.ip.ip.ip iburst trust |
Siendo Where ip.ip.ip.ip
la dirección IP de la máquina de is the IP address of the OpenGate Proxy Server , en la que previamente se ha activado el servidor NTP (consultar pinstallgudemachine, where the NTP server has been previously activated (refer to the Presence installation guide).
Email service
En el Master es necesario instalar “postfix” para poder enviar los emails de buzones de vozOn the Master, it is necessary to install "postfix" in order to send voicemails:
Code Block |
---|
sudo dnf install postfix sudo systemctl --now enable postfix |